Excavator Comparison

Linde 2PV-TS Hydraulic Pump – An Introduction

komatsuvscat 

Linde 2PV-TS Hydraulic Pump is an all-purpose hydraulic pump that has been designed for use on Linde equipment such as excavators and wheel loaders. It can also be used on other manufacturers’ vehicles that require a hydraulic pump with a maximum capacity of 6,670 litres per minute and a maximum pressure of 1,100 bar. The pump itself is driven by an electric motor with an output of 24 kW and it comes complete with its own oil reservoir, which has a volume of 13 litres. This means that you do not have to worry about refilling the oil tank every time you use the pump, as it will simply refill itself automatically when it runs out of fluid.

The 2PV-TS model has been designed to be used both indoors and outdoors, so it should not matter whether you are working in the warehouse or out on site with this unit installed on your machine. It has also been designed to run quietly when in operation so your neighbours will not be disturbed by noise pollution during use.

Linde 2PV-TS Hydraulic Pump is one of the world’s leading manufacturers of drive systems and hydraulic components.

The 2PV-TS is a high-pressure double-acting plunger pump with two pistons that move in opposite directions. The pistons are mounted on one shaft with a common crankpin. This allows the pistons to be driven by a single motor via a double-clutch mechanism or by two separate motors through chains or belts. This design offers considerable cost savings, particularly in mass production applications where the same pump may have to be used in different machines.

Linde double-acting plunger pumps are available in capacities up to 12 liters per minute at pressures up to 300 bar (4350 psi). They are suitable for general industrial use and for pumping liquids such as water and oil under pressure, as well as for handling slurries and suspensions.

Linde 2PV-TS Hydraulic Pump – An Introduction
Linde 2PV-TS Hydraulic Pump – An Introduction

The 2PV-TS hydraulics pump is designed for use in a wide range of applications, including indoor and outdoor material handling equipment.

Linde has developed an innovative drive technology that improves the efficiency of hydraulic pumps. The 2PV-TS features a new technology that allows it to operate at lower speeds and with fewer moving parts than traditional pumps. This enables it to deliver high performance at low RPMs over its entire operating range, which results in lower noise levels and less wear on critical components.

The 2PV-TS offers a compact design with only one moving part and no shaft seals, making it ideal for mobile applications where space is limited. It also features an integrated pressure relief valve that protects against excessive pressures caused by system leaks or surges.

The 2PV-TS pump is a variable displacement axial piston pump.

The Linde 2PV-TS hydraulic pump is a medium capacity, compact design that can be used for high pressure applications. This includes its ability to pump viscous fluids such as grease, oils and even some liquids. The unit features a unique design that allows for quick changeover from one material to another without any tools required. The Linde 2PV-TS is also capable of handling temperatures up to 350°F (177°C).

The Linde 2PV-TS Hydraulic Pump is designed with an integrated oil cooler which provides cooling for the internal parts in order to prevent overheating. The unit also has an automatic spring return feature which helps make it easier to refill the oil reservoir if necessary.

The 2PV-TS operates with minimum noise levels and has low vibration under all working conditions.

The 2PV-TS is a high-pressure, single acting hydraulic pump for the transfer of clean fluids. The 2PV-TS can be used for a wide range of applications including agricultural vehicles, construction machines and trucks, industrial vehicles and equipment.

In addition to its high pressure capability, the 2PV-TS provides excellent performance at low pressure levels as well. It is available in a variety of configurations with either cast iron or aluminum alloy heads and feet. All components are made from first quality materials and are manufactured in accordance with ISO 9001:2008 standards.

The Linde 2PV-TS is quiet and vibration free under all working conditions. It has been designed to run with minimum noise levels and has low vibration under all working conditions. This characteristic makes it an ideal choice for use in residential areas where it can be installed without disturbing residents or neighbors. The continuous operation of this pump also reduces the need for maintenance downtime which results in lower overall operating costs compared to other types of pumps available on the market today.

The 2PV-TS offers exceptional flow control, stability and reliability due to its variable displacement capacity.

The Linde 2PV-TS is a compact, highly efficient single-stage axial piston pump with integrated valve actuator. The double acting piston moves in both directions within the cylinder bore by means of an external eccentric shaft. The piston is guided in its movement by two rollers.

A flow control device allows the operator to adjust the flow rate from zero to maximum capacity at all times. The high pressure piston valve can be preset to any position between full flow and zero flow and thus acts as an integrated valve actuator. This feature makes it possible to build up pressure quickly during start-up and ensures excellent start-up behaviour even under difficult conditions such as low viscosity or high temperature changes.

The 2PV-TS can be configured as a stand alone unit or part of a modular system.

The Linde 2PV-TS pump is a single-stage, vertical split case, hydraulic pump with an integrated electronic control unit. It is designed for use as a stand-alone unit or in conjunction with other Linde 2PV-TS pumps to create a modular system. The pump can be configured for operation at pressures up to 6,000 bar (90 MPa).

The 2PV-TS has been designed to meet the requirements of the latest generation of high-pressure firefighting vehicles, which are required to have higher pumping capacities than ever before. It also offers high efficiency and reliability in all conditions including hot/cold temperatures and low air pressure. The 2PV-TS can be used both on land and water with no additional modifications required.

There are four main configurations available for the Linde 2PV-TS hydraulic pump.

There are four main configurations available for the Linde 2PV-TS hydraulic pump. The standard configuration is a single stage hydraulic pump with an integrated hydraulic motor. The second configuration is a double stage hydraulic pump with an integrated hydraulic motor. This configuration can be used for continuous pumping or intermittent pumping where the flow rate through each stage is reduced by restricting the flow in one of the stages, allowing for periodic shut downs without having to cool down the entire system. The third configuration is a double stage hydraulic pump with separate hydraulic motors on each side of the gearbox. This set up allows you to use one side of the gearbox as a pressure relief valve if necessary. The fourth configuration is a single stage hydraulic pump with separate hydraulic motors on each side of the gearbox and an external relief valve between them both. This allows for more flexibility in how you want to set up your system because it allows you to choose whether or not you want two pumps running simultaneously or just one of them running at all times.

Linde 2PV-TS Hydraulic Pump – An Introduction
Linde 2PV-TS Hydraulic Pump – An Introduction

For maximum efficiency and lowest possible operating costs, the Linde 2PV-TS Pump should be matched to your specific application requirements.

The 2PV-TS is equipped with a balanced flange connection and an integrated pressure relief valve. The pump can be connected directly to the fluid reservoir or to a pipe network via a flexible coupling. The 2PV-TS can also be used with an electric motor as an electrically driven pump.

The 2PV-TS has been designed for continuous operation at temperatures up to 120 °C (250 °F). The maximum operating temperature does not apply when using oil or other fluids which are known for their reduced thermal conductivity at elevated temperatures.

This guide gives an introduction to the drivers behind the design, features and uses of the ISO standard compliant Linde Hydraulics 2PV-TS variable displacement axial piston pump

The Linde 2PV-TS is an ISO standard compliant variable displacement axial piston pump. It uses an adjustable displacement to control flow rate. The pump has been designed to meet the requirements of the latest ISO standards, including ISO 6709, which specifies a new approach to rating and classifying pumps.

The 2PV-TS can be used as a hydraulic power unit in mobile applications such as agriculture, construction and industry. It is suitable for use with low viscosity fluids (up to 4 000 cSt), such as lubricating oils, power steering fluid or synthetic oils for machine tools.

As you can see, the Linde 2PV-TS Hydraulic Pump is a reliable, high-quality pump that should help you get the job done. The fact that it’s hydraulically driven means less wear and tear on your machine and lower operating costs over time.

Recommended Posts

Danfoss 90 Series Hydraulic Pump Review
Excavator Comparison

Danfoss 90 Series Hydraulic Pump Review

Danfoss is a manufacturer of hydraulic pumps and motors. They have several series of hydraulic pumps, including the 90 series. The Danfoss 90 series is a compact and lightweight centrifugal pump, making it ideal for mobile applications. The Danfoss 90 series is also available in three different sizes, allowing you to select the best pump […]

komatsuvscat

Leave A Comment