what is the flow rate on a pc 200-3 komatsu excavator
The Condar 200 series is one of the most popular excavator selection in Australia. As one of the best Komatsu service in Melbourne, we get many of those machines. In this blog, I will walk you through on how to calculate the flow rate on an excavator.
pc 200-3 komatsu excavator-The hydraulic flow rate on a Komatsu Pc 200-3 is 264 gallons per minute.
The hydraulic flow rate on a Komatsu Pc 200-3 is 264 gallons per minute. The hydraulic pump output rating is 87 horsepower. The Komatsu PC 200-3 excavator is equipped with an air system that requires 0.2 cubic feet of air per minute at a pressure of 100 psi. Its fuel tank has a capacity of 53.6 gallons, and it weighs 47,350 pounds.
The Komatsu PC 200-3 is manufactured in Japan by Komatsu Ltd., which was founded in 1921 as Komatsu Iron Works to manufacture mining equipment. Komatsu became the world’s second largest manufacturer of construction and mining equipment in 2011 after acquiring the U.S.-based company Joy Global, Inc.
pc 200-3 komatsu excavator-The hydraulic flow rate is two times the pump flow rate.
The hydraulic flow rate is two times the pump flow rate. For instance, if a pump has a maximum flow of fifty-five gallons per minute, then the hydraulic system on that machine will flow at one hundred and ten gallons per minute.
This might sound like more than enough oil for any job, but keep in mind that the machine has to power many different attachments. If a bucket is being filled as fast as possible with dirt, it’s not unusual for an excavator to use up most of its hydraulic flow just powering that motion.
pc 200-3 komatsu excavator-If for any reason the heat exchanger of the engine gets blocked, a by-pass valve will allow coolant to continue flowing to the engine.
The Komatsu PC200-3 excavator was manufactured from 1993 until 1998. The cooling system of the excavator is a closed loop system that uses a constant flow pump to circulate coolant through the engine block and radiator. If for any reason the heat exchanger of the engine gets blocked, a by-pass valve will allow coolant to continue flowing to the engine.
The flow rate of the cooling system is controlled by a thermostat located on the front side of the heat exchanger. The thermostat measures the temperature of coolant as it leaves the heat exchanger and opens at 80 degrees Celsius, or 176 degrees Fahrenheit. When open, the thermostat allows coolant to flow through the heat exchanger at a rate of 200 litres per minute or 53 gallons per minute.
pc 200-3 komatsu excavator-To prevent blockages from occurring in your heat exchanger, keep your radiator core and air passages clean.
A flow rate is the amount of liquid that flows through a given area for a certain amount of time, and is measured by gallons per minute (GPM). The flow rate is determined by the equipment used and some conditions of the job. For example, if a flow rate is needed for setting up a sprayer, it will be different than when using a pump to apply fertilizer.
The heat transfer rate depends on the heat exchanger configuration, the operating temperature, and the flow rates and heat capacities of the two fluids. The overall heat transfer coefficient U is based on an A1-A2 heat transfer surface area .
The flow rate through a heat exchanger may be controlled by use of a pump in either one or both of the fluid circuits:
Forced-convection and single-phase fluid flow in pipes and channels are fundamental processes for heat transfer in many engineering applications. In particular, these types of flows are important for electronic cooling, liquid cooling in nuclear reactors as well as air-cooling technologies.
pc 200-3 komatsu excavator-The maximum pressure that the hydraulic system can generate is 4,580 psi.
The maximum pressure that the hydraulic system can generate is 4,580 psi. The flow rate of the pump is 57 gallons per minute at a speed of 2,100 rpm. The hydraulic system allows the bucket to be raised and lowered and for the boom to be positioned in various positions without an operator’s assistance.
The Komatsu PC200-3 features a 7’5″ digging depth and weighs 52,620 pounds. It has a 6 foot, 8 inch track gauge and uses a turbocharged diesel engine. The engine has six cylinders and a displacement of 3.2 liters. It produces 150 horsepower at 1,800 rpm. The engine can travel at speeds up to 9 miles per hour when moving forward or 3 miles per hour while in reverse.
The Komatsu PC200-3 has an operating weight of 43,940 pounds with the canopy installed or 44,330 pounds with the cab installed. The canopy provides protection against weather conditions such as rain or snow but does not include windows for viewing out of the cab.
pc 200-3 komatsu excavator-The hydraulic reservoir can hold a maximum of 50 gallons of hydraulic fluid.
The hydraulic reservoir can hold a maximum of 50 gallons of hydraulic fluid. The hydraulic pump can supply 41 gallons of fluid per minute. The PC200-3 excavator uses a standard rotating control device (ROC) and the PC210-3 uses an ROC with a lifting arm.
The Komatsu PC200-6 medium excavator is designed for those who need power and performance. The PC200-6 has the same horsepower as the previous model, but the PC200-6 has less operating weight and more bucket digging force. This machine has a maximum digging depth of 18 feet 2 inches with a maximum digging reach of 29 feet 6 inches.
pc 200-3 komatsu excavator-Hydraulic excavators depend on a combination of high pressure and high flow rates in order to work well.
Hydraulic excavators depend on a combination of high pressure and high flow rates in order to work well. The hydraulic pumps in excavators are capable of creating a wide range of pressures, but the pump can only create so much flow. This is why it’s important to match an excavator with the right hydraulic pump.
An excavator’s hydraulic pump affects how quickly its various functions can operate. It also affects how fast you can move material with your bucket and how fast you can dig. As such, it’s important to match the right pump to your excavator’s engine, so that the engine doesn’t run out of gas while the pump waits for it to catch up.
A good example is the Komatsu PC 200LC-3 model; this excavator is equipped with a Komatsu SAA6D102E-2 diesel engine that has a power output of 114 kilowatts at 2,000 revolutions per minute. The SAA6D102E-2 engine is rated for a maximum torque of 590 Newton meters at 1,500 RPM.